1: LID_OPENED/上盖开
Error code 1:0
Reason: The lid was opened while the print engine was performing an operation. Close the lid and try again.
//打印机工作时上盖开，关闭上盖重试
Error code 1:1
Reason: The lid was open at the point the printer was about to begin a print job. Close the lid and try again.
//打印机在开始一个打印任务时上盖开，关闭上盖重试
2: OUT_OF_CARDS//无卡
Error code 2:5
Reason: While feeding a card from the hopper, it took too long for the rear sensor to block.
//从卡盒进卡时，后面卡传感器长时间未感觉到卡片.建议检查卡盒是否有卡或卡片是否由于静电等原因粘在一起
Error code 2:6
Reason: While trying to feed a card from the hopper, it took too long for the front sensor to block.
//从卡盒进卡时，前面卡传感器长时间未感觉到卡片（此时应该后面和中间传感器有所感应）
3: NO_HAND_FEED//手动进卡错误
Error code 3:0
Reason: While hand feeding a card, it took too long for the front sensor to block.
//前方手动进卡时前传感器长时间未感应到卡片
Error code 3:1
Reason: While hand feeding a card, it took too long for the hopper sensor to detect a card.
//手动进卡时后传感器长时间未感应到卡片
4: CARD_JAM//卡住卡片
Error code 4:0
Reason: While moving the card forwards to the front sensor in preparation for placing it in the contactless encoding position, it took too long for the front sensor to block.
//当打印机向前传感器移卡准备到非接触IC位置时，前卡传感器长时间未感觉到卡片
Error code 4:1
Reason: While moving the card backwards from the front sensor to the contactless encoding position, it took too long for the front sensor to unblock.
//当打印机从前卡传感器向后移卡到非接触IC位置时，前卡传感器始终感应到卡片
Error code 4:2
Reason: While feeding a card from the smart encoder to the flipper, it took too long for the smart extract sensor to indicate that the card was free of the encoder.
//当从接触IC模块退卡到翻转器时，IC卡传感器始终能感觉到卡片（可能卡片一直在IC模块中或传感器故障）
Error code 4:3
Reason: While moving a card from the flipper into the smart encoder, it took too long for the smart insert sensor to trigger.
//当从翻转器进卡到IC接触模块位置时，IC模块传感器长时间未感觉到卡片
Error code 4:4
Reason: While moving the card from the flipper to the standby position, it took too long for the mid sensor to block.
//从翻转器往打印位置移动卡片时，中间卡传感器长时间未感应到卡片
Error code 4:7
Reason: While feeding a card from the hopper, and having seen the card reach the rear sensor, it took too long for the mid sensor to block.
//从进卡盒进卡，后面卡传感器感应到卡片，但是中间卡传感器长时间未感应到卡片
Error code 4:8
Reason: While feeding a card from the hopper, and having seen the card reach the mid sensor, it took too long to clear the rear sensor by rewinding the feed motor.
//从进卡盒进卡，中间的卡传感器感应到卡片，但是后卡传感器始终感觉到卡片
Error code 4:9
Reason: While moving the card forwards to feed into the flipper, it took too long for the card's leading edge to block the front sensor.
//移动卡片向前至翻转器，卡片前端长时间未能阻断前卡传感器
Error