Error code 1:0
Reason: The lid was opened while the print engine was performing an operation. Close the lid and try again.
//打印机工作时上盖开，关闭上盖重试
Error code 1:1
Reason: The lid was open at the point the printer was about to begin a print job. Close the lid and try again.
//打印机在开始一个打印任务时上盖开，关闭上盖重试
2: OUT_OF_CARDS//无卡
Error code 2:5
Reason: While feeding a card from the hopper, it took too long for the rear sensor to block.
//从卡盒进卡时，后面卡传感器长时间未感觉到卡片.建议检查卡盒是否有卡或卡片是否由于静电等原因粘在一起
Error code 2:6
Reason: While trying to feed a card from the hopper, it took too long for the front sensor to block.
//从卡盒进卡时，前面卡传感器长时间未感觉到卡片（此时应该后面和中间传感器有所感应）
3: NO_HAND_FEED//手动进卡错误
Error code 3:0
Reason: While hand feeding a card, it took too long for the front sensor to block.
//前方手动进卡时前传感器长时间未感应到卡片
Error code 3:1
Reason: While hand feeding a card, it took too long for the hopper sensor to detect a card.
//手动进卡时后传感器长时间未感应到卡片
4: CARD_JAM//卡住卡片
Error code 4:0
Reason: While moving the card forwards to the front sensor in preparation for placing it in the contactless encoding position, it took too long for the front sensor to block.
//当打印机向前传感器移卡准备到非接触IC位置时，前卡传感器长时间未感觉到卡片
Error code 4:1
Reason: While moving the card backwards from the front sensor to the contactless encoding position, it took too long for the front sensor to unblock.
//当打印机从前卡传感器向后移卡到非接触IC位置时，前卡传感器始终感应到卡片
Error code 4:2
Reason: While feeding a card from the smart encoder to the flipper, it took too long for the smart extract sensor to indicate that the card was free of the encoder.
//当从接触IC模块退卡到翻转器时，IC卡传感器始终能感觉到卡片（可能卡片一直在IC模块中或传感器故障）
Error code 4:3
Reason: While moving a card from the flipper into the smart encoder, it took too long for the smart insert sensor to trigger.
//当从翻转器进卡到IC接触模块位置时，IC模块传感器长时间未感觉到卡片
Error code 4:4
Reason: While moving the card from the flipper to the standby position, it took too long for the mid sensor to block.
//从翻转器往打印位置移动卡片时，中间卡传感器长时间未感应到卡片
Error code 4:7
Reason: While feeding a card from the hopper, and having seen the card reach the rear sensor, it took too long for the mid sensor to block.
//从进卡盒进卡，后面卡传感器感应到卡片，但是中间卡传感器长时间未感应到卡片
Error code 4:8
Reason: While feeding a card from the hopper, and having seen the card reach the mid sensor, it took too long to clear the rear sensor by rewinding the feed motor.
//从进卡盒进卡，中间的卡传感器感应到卡片，但是后卡传感器始终感觉到卡片
Error code 4:9
Reason: While moving the card forwards to feed into the flipper, it took too long for the card's leading edge to block the front sensor.
//移动卡片向前至翻转器，卡片前端长时间未能阻断前卡传感器
Error code 4:13
Reason: While moving the card from the front sensor to the standby position, it took too long for the front sensor to unblock.
//从卡前传感器移至打印位置时，前卡传感器始终感应到卡片
Error code 4:14
Reason: While moving the card from the rear sensor to the standby position, it took too long for the rear sensor to unblock.
//从后卡传感器移卡至打印位置，后卡传感器始终感应到卡片
Error code 4:15
Reason: While moving a card from the flipper into the smart encoder, it took too long for the smart extract sensor to trigger. This may mean that there is no encoder actually fitted.
//从翻转器移卡至接触IC模块，模块传感器长时间未能感应到卡片，机器可能未装IC模块，主板与IC模块的连接线未接或传感器异常
Error code 4:16
Reason: While feeding a card past a sensor, and having seen the card reach that sensor, it took too long for the sensor to unblock.
//当卡片通过传感器时，传感器感应到卡片，但是卡片通过后始终处于阻断状态
Error code 4:17
Reason: While moving the card into position for a printing or encoding operation, it took too long for the reference edge of the card to move in front of the sensor used for positioning. In the case of extended mono prints, this means the mid sensor took too long to block. In other cases, this means it took too long for the rear sensor to unblock.
//当移动卡片到相应的位置打印或编码时，卡片参考边缘长时间未能通过相应传感器；对于 EXTENDED单色打印来说，这意味着中间卡传感器长时间未能感应到卡片；对于其他机器来说，后卡传感器始终感应到卡片
Error code 4:18
Reason: While moving the card into position for a printing or encoding operation, it took took long for the reference edge of the card to move behind the sensor used for positioning. In the case of extended mono prints, this means the mid sensor took too long to unblock. In other cases, this means it took too long for the rear sensor to block.
//当移动卡片到相应的位置打印或编码时，卡片参考边缘长时间未能通过相应传感器；对于 EXTENDED单色打印来说，这意味着中间卡传感器长时间感应到卡片；对于其他机器来说，后卡传感器始终未感应到卡片
Error code 4:19
Reason: While trying to eject the card, it took too long for the leading edge of the card to block the front sensor.
//退卡时，前卡传感器始终未感应到卡片前端
Error code 4:20
Reason: While trying to eject the card, and having seen the leading edge of the card reach the front sensor, it took too long for the front sensor to unblock.
//退卡时前卡传感器感应到卡片，但是始终未能清空前卡传感器
Error code 4:21
Reason: While moving the card from the flipper to the standby position, and having seen the card reach the mid sensor, it took too long for the mid sensor to unblock.
//当从翻转器移卡到打印位置时，看到卡片到达中卡传感器，但是中间卡传感器始终未清空
Error code 4:22
Reason: While trying to feed a card from the hopper, and having seen the card reach the front sensor, it took too long for the front sensor to unblock.
//从卡盒进卡，前卡传感器感应到卡片，但是前卡传感器始终未清空
Error code 4:23
Reason: While moving the card backwards to feed into the flipper, it took too long for the card to block the mid sensor.
//卡片后移进入翻转器时，中间卡传感器长时间未感应到卡片
Error code 4:24
Reason: While moving the card from the mid sensor to the standby position, it took too long for the mid sensor to unblock.
//卡片从中卡传感器移往打印位置时，中卡传感器长时间未清空
5: OUT_OF_FILM//无色带
Error code 5:0
Reason: While moving a dye panel edge from the dye sensor to the printhead, it took too long for the tacho wheel to move the required amount. The film has probably either run out or snapped.
//从色带传感器移动色带面到打印头，色带计数器转动所需的计数时间太久.可能是色带用完了或断了
Error code 5:1
Reason: While advancing to the next dye panel, it too long for the next panel boundary to be detected.
//移动色带至下一面时，长时间无法检测到色带面边界
Error code 5:2
Reason: It took too many attempts for the printer to find a particular panel of dye film (possibly because the dye sensor needs calibration).
//打印机偿试太多次来寻找某一特定的色带面（可能是因为色带传感器需要校验）
Error code 5:3
Reason: A valid dye film RFID tag was found, but no physical ribbon could be detected while trying to take up the film slack.
//已检测到有效的色带芯片，但是初始化色带时未发现物理色带（可能色带断了）
Error code 5:4
Reason: A valid dye film RFID tag was found, but there were no shots remaining.
//检测到有效的色带芯片，但是色带已用完
Error code 5:5
Reason: After printing a card, the printer was unable to decrement the number of remaining prints on the dye film RFID tag.
//打印后打印机无法减少色带RFID芯片上的色带剩余计数
Error code 5:6
Reason: While advancing the dye film, the printer detected the end-of-film marker.
//移动色带至下一面时，打印机检测到色带用完标记
Error code 5:7
Reason: While moving the dye film, too great a time elapsed between tacho sensor counts. The film has probably either run out or snapped.
//移动色带时，色带计数器之间的计数时间间隔太长.可能是色带用完了或断了
Error code 5:8
Reason: While trying to take up the film slack, no tacho pulses were observed within a reasonable amount of time
//在偿试拉紧色带时，在合理的时间间隔内未检测到色带计数器脉冲
6: FILM_INVALID//色带无效
Error code 6:0
Reason: The fitted dye film had an invalid RFID tag. Either the tag was not programmed correctly or there is a problem with the RFID tag reader.
//色带芯片无效.可能是色带芯片编码错误或者芯片读取错误
Error code 6:1
Reason: A dye film ribbon was detected, but a valid dye film RFID tag could not be found. This printed is not configured to permit tagless film.
//检测到色带但是未发现有效芯片.此打印机仅能使用带芯片色带
Error code 6:2
Reason: The fitted dye film does not have the right region code for this printer. Try another roll of film.
//安装的色带与打印机的地区代码不符，请联系您的供应商确定
Error code 6:3
Reason: The fitted dye film does not have the right dealer code for this printer. Try another roll of film.
//安装的色带代理商编码与打印机不符，请联系您的供应商确定
Error code 6:4
Reason: The fitted dye film does not have the right project code for this printer. Try another roll of film.
//安装的色带项目编码与打印机不符，请联系您的供应商确定
Error code 6:5
Reason: The fitted dye film does not have the right grade code for this printer. Try another roll of film.
//安装的色带等级代码与打印机不符，请联系您的供应商确定
7: REMOVE_FILM//取出色带
Error code 7:0
Reason: The printer detected film was loaded when trying to calibrate dye LEDs and dye motor.
//打印机在偿试校验色带传感器和马达时检测到色带已安装，请取下色带继续
Error code 7:3
Reason: The printer detected film was loaded when trying to carry out an operation that requires no film to be present.
//打印机在偿试其他无色带操作时检测到色带已安装，请取下色带继续
8: CAM_JAM//凸轮机构卡住
Error code 8:0
Reason: While moving the printhead cam to the closed position, it took too long to detect the trailing edge of the cam pulley flag.
//移动打印头凸轮至关闭位置，长时间未检测到凸轮齿轮的突出边缘
Error code 8:1
Reason: While initialising the cam, it took too long to detect the leading edge of the cam pulley flag.
//初始化凸轮机构时，长时间未检测到凸轮齿轮的起始边缘标记
Error code 8:2
Reason: While initialising the cam, and having detected the leading edge of the cam pulley flag, it took too long to detect the trailing edge of the flag.
//初始化凸轮机构时，已检测到凸轮齿轮的起始边缘标记，但是长时间未清空传感器
Error code 8:3
Reason: While moving the printhead cam to the open position, it took too long to detect the leading edge of the cam pulley flag.
//移动打印头凸轮至打开位置时，长时间未检测到凸轮齿轮的起始边缘标记
9: FLIP_JAM//翻转器卡住
Error code 9:0
Reason: While initialising the flipper, it took too long to detect the start of the blocked region of the flange.
//初始化翻转器时长时间未检测到翻转器齿轮的突起起始位置
Error code 9:1
Reason: While initialising the flipper, and having detected the start of the blocked region of the flange, it took too long to detect the start of the unblocked region (the start of the slot).
//初始化翻转器时，已检测到翻转器齿轮的突起开始位置，但是长时间未检测到开孔起始位置
Error code 9:2
Reason: While moving the card backwards to feed into the flipper, and having seen the card arrive at the mid sensor, it took too long for the mid sensor to unblock.
//向后移动卡片进翻转器时，中间的卡感应器感应到卡片，但是长时间未清空中间卡传感器
10: FILE_INVALID//文件无效
Error code 10:0
Reason: The printer received a print job. The side number specified for one of the sides of the image data was invalid. This probably means the print job file was corrupt.
//打印机接收到打印任务，部分图像数据无效，可能打印任务已损坏
Error code 10:1
Reason: The printer received a print job. The format specified for the image payload was not supported. If updating the firmware does not fix this, it may be that the print job file is corrupt.
//打印机接收到打印任务，打印机不支持任务中指定的格式，请更新打印机监控程序和驱动，如果无法解决，可能打印任务已损坏
Error code 10:2
Reason: The printer received a print job containing magnetic track data. One of the tracks specified an invalid track number.
//打印机接收到的任务包括磁条数据，其中一个磁轨指定了无效的磁轨编号
Error code 10:3
Reason: The printer received a print job containing magnetic track data. The number of bits specified for one of the tracks was out of range. This probably means that the print job file was corrupt.
//打印机接收到的任务包括磁条数据,其中一个磁轨指定的位数已超限，可能打印文件已损坏
Error code 10:4
Reason: The printer received a print job containing magnetic track data. The number of bits specified for one of the tracks was too great for the provided payload size. This probably means that the print job file was corrupt.
//打印机接收到的任务包括磁条数据，其中一个磁条指定的位数远超有限负载，可能打印文件已损坏
Error code 10:5
Reason: The printer received a print job containing magnetic track data. The bit density specified for one of the tracks was out of range. This probably means that the print job file was corrupt.
//包括磁条数据的打印任务已损坏
Error code 10:6
Reason: The printer received a print job. The panel ID specified for one of the panels was invalid. This probably means that the print job file was corrupt.
//打印机接收到一打印任务，指定的面数ID无效，可能打印文件已损坏
Error code 10:7
Reason: The printer received a print job. The width or height specified for the card was out of range. This probably means the print job file was corrupt.
//打印机接收到一打印任务，卡片定义的尺寸超限. 可能打印文件已经损坏
Error code 10:8
Reason: The printer received a print job. The payload provided was not large enough to hold the image width specified. This probably means the print job file was corrupt.
//打印机接收到打印任务，指定的负载容量不足以承载指定的图像宽度，可能打印文件已损坏
Error code 10:9
Reason: The printer received a print job. The power adjustment for one of the panels was out of range. This probably means the print job file was corrupt.
//打印机接收到打印任务，色带面的能量调整超限，可能打印文件已损坏
Error code 10:11
Reason: The printer received a print job. The number of copies specified was less than 1. This means that the print job file is corrupt.
//打印机接收到打印任务，打印份数小于1，可能打印文件已损坏
Error code 10:12
Reason: The printer received a print job containing magnetic track data. The number of encoding attempts requested was less than one.
//打印机接收到的任务包括磁条数据，编码次数小于1
Error code 10:13
Reason: The printer received a print job containing magnetic track data. The number of verification attempts requested was less than zero.
//打印机接收到的任务包括磁条数据，磁条校验次数小于1
Error code 10:14
Reason: The printer received a print job. The x adjustment specified for a panel was out of range. This probably means the print job file was corrupt.
//打印机接收到打印任务，一面指定的X调整超限，可能打印任务已损坏
Error code 10:15
Reason: The printer received a print job. The y adjustment specified for a panel was out of range. This probably means the print job file was corrupt.
//打印机接收到打印任务，一面指定的Y调整超限，可能打印任务已损坏
Error code 10:16
Reason: The printer received a print job. An area or hole setting for one of the panels was missing a required element. This probably means the print job file was corrupt.
//打印机接收到打印任务，其中设定的区域或预留区缺少必要元素，可能是打印文件已损坏
Error code 10:17
Reason: The printer received a print job. An area or hole setting for one of the panels had an out-of-range value. This probably means the print job file was corrupt.
//打印机接收到打印任务，其中设定的区域或预留区的值超限，可能是打印文件已损坏
Error code 10:18
Reason: The printer received a print job. The X coordinate for the HoloCode is out of range. This probably means the print job file was corrupt.
//打印机接收到打印任务，HoloCode的X坐标超限，可能打印文件已损坏
Error code 10:19
Reason: The printer received a print job. The Y coordinate for the HoloCode is out of range. This probably means the print job file was corrupt.
//打印机接收到打印任务，HoloCode的Y坐标超限，可能打印文件已损坏
Error code 10:20
Reason: The printer received a print job. The module size for the HoloCode is out of range. This probably means the print job file was corrupt.
//打印机接收到打印任务，HoloCode的模块尺寸超限，可能打印文件已损坏
Error code 10:21
Reason: The printer received a print job. The margin for the HoloCode is out of range. This probably means the print job file was corrupt.
//打印机接收到打印任务，HoloCode的边距超限，可能打印文件已损坏
Error code 10:22
Reason: The printer received a print job. The format for the HoloCode is unsupported. This probably means the print job file was corrupt.
//打印机接收到打印任务，不支持此HoloCode格式，可能打印文件已损坏
Error code 10:23
Reason: The printer received a print job. The data for the HoloCode is either empty or too long. This probably means the print job file was corrupt.
//打印机接收到打印任务，此HoloCode数据为空或太长，可能打印文件已损坏
11: SOFTWARE_OUTDATED//软件过期
Error code 11:0
Reason: The fitted dye film has a data format which the printer could not understand. The printer software needs to be upgraded in order to support this type of dye film.
//打印机不支持安装色带的数据格式，请更新打印机监控程序
12: SENSOR_FAILURE//传感器失效
Error code 12:0
Reason: While hand feeding a card, the rear sensor blocked before the front one.
//手动进卡时后卡传感器比前卡传感器早感觉到卡片
Error code 12:1
Reason: While hand feeding a card, and having seen the card reach the front sensor, the rear sensor blocked before the front sensor unblocked.
//手动进卡时，前卡感应器感应到卡片，但是前卡传感器还未清空后卡传感器就感应到了卡片
Error code 12:3
Reason: While feeding a card from the hopper, the front sensor blocked before the mid one.
//后卡盒进卡，前卡感应器比中卡感应器早感应到卡片
Error code 12:4
Reason: While feeding a card from the hopper, the front sensor blocked before the rear one.
//后卡盒进卡，前卡感应器比后卡感应器早感应到卡片
Error code 12:5
Reason: While trying to feed a card from the hopper, the mid sensor triggered before the rear one.
//后卡盒进卡，中卡感应器比后卡感应器早感应到卡片
13: INTERNAL_ERROR//内部错误
Error code 13:1
Reason: The printhead took too long to reach a temperature suitable for printing. There may be a fault with the printhead temperature sensor.
//打印头温度不够，可能打印头温度传感器损坏
Error code 13:2
Reason: The mag PCB MCU reported that an error occurred while trying to carry out an operation or interpret a command.
//在偿试完成操作或执行指令时磁条PCB MCU报告发生错误
Error code 13:3
Reason: The mag driver reported that an error occurred while trying to carry out an operation.
//偿试完成操作时磁条驱动报告发生错误
Error code 13:4
Reason: Communication with the print engine microcontroller failed. If rebooting the printer does not fix this problem, try updating the firmware. If that does not work, there is probably a hardware fault.
//打印机内部通讯失败. 如果重新启动打印机无法解决问题，请偿试更新监控程序，如果还是无法解决，可能是打印机硬件故障（主板,SD卡或主板上小板）
Error code 13:5
Reason: The print engine microcontroller reported an error. If rebooting the printer does not fix this problem, try updating the firmware. If that does not work, there is probably a hardware fault.
//打印机微控制单元报错. 如果重新启动打印机无法解决问题，请偿试更新监控程序，如果还是无法解决，可能是打印机硬件故障（主板,SD卡或主板上小板）
Error code 13:6
Reason: During initialisation the printer could not program the FPGA. Ensure the printer is running the latest software, reboot the printer, and try again. If this does not work there is either a bug in the printer software or a hardware fault.
//初始化期间打印机无法对FPGA编程，请确保打印机安装最新的监控版本，重新启动打印机重试，如果仍然无法解决，可能是软件BUG或硬件故障
14: SD_CARD_UNSIGNED//SD卡未签名
Error code 14:0
Reason: The internal SD card did not have a valid signature.
//打印机SD卡无有效签名
15: HOLOKOTE_INVALID//HOLOKOTE无效
Error code 15:0
Reason: While attempting to validate a Holokote file, the printer found that the file was not in the right format. Either it is not the right type of file, or the data has been corrupted.
//试图验证Holokote文件时，打印机发现该文件的格式不正确. 文件格式错误或者数据已损坏
16: HOLOKOTE_NOT_AUTH//HOLOKOTE未授权
Error code 16:0
Reason: While attempting to validate a Holokote file, the printer found that the file was not licensed for this printer. It is possible that the file was intended for a different printer.
//偿试HOLOKOTE文件时，打印机发现此为非本打印机授权文件，此文件可能是其他打印机的授权文件
17: UPGRADE_INVALID//无效升级
Error code 17:0
Reason: While attempting to validate an upgrade file, the printer found that the file was not in the right format. Either it is not the right type of file, or the data has been corrupted.
//打印机验证升级文件，文件格式不对，可能是文件类型错误或数据已损坏
Error code 17:1
Reason: While attempting to validate an upgrade file, the printer found that the file was not in the right format. Either it is not the right type of file, or the data has been corrupted.
//打印机验证升级文件，文件格式不对，可能是文件类型错误或数据已损坏
Error code 17:2
Reason: While attempting to validate an upgrade file, the printer could not interpret the file's upgrade commands. Either it is not the right type of file, or the data has been corrupted.
//打印机验证升级文件，无法解释文件的升级指令，可能是文件类型错误或数据已损坏
18: UPGRADE_NOT_AUTH//升级未授权
Error code 18:0
Reason: While attempting to validate an upgrade file, the printer found that the file was not licensed for this printer. It is possible that the file was intended for a different printer.
//打印机验证升级文件，文件未对此打印机授权，可能此文件为另一台打印机的升级文件
19: SOFTWARE_INVALID//软件无效
20: SD_WRITE_FAILED//SD写入失败
Error code 20:0
Reason: While performing a system software update, an error occurred while trying to write temporary update data to the SD card.
//系统软件更新时，向SD卡中写入临时升级数据时发生错误
Error code 20:2
Reason: While attempting to apply an upgrade, the printer was unable to create the upgrade directory on the SD card. Either the SD card is missing, unformatted or functioning incorrectly.
//偿试进行升级时，打印机无法在SD卡中生成升级目录. 可能无SD卡，未格式化或功能出错
Error code 20:3
Reason: While attempting to install a custom Holokote image, the printer was unable to create the overcoat directory on the SD card. Either the SD card is missing, unformatted or functioning incorrectly.
//偿试安装定制HOLOKOTE水印时，打印机无法在SD卡中生成保护层目录.可能是无SD卡，未格式化或功能出错
Error code 20:4
Reason: While attempting to update the system image, the printer was unable to create the system upgrade directory on the SD card. Either the SD card is missing, unformatted or functioning incorrectly.
//偿试更新系统数据时，打印机无法在SD卡中生成系统更新目录.可能是无SD卡，未格式化或功能出错
Error code 20:5
Reason: While attempting to format the SD card at the start of a soak routine, the formatting process failed.
//偿试在SOAK测试开始时格式化SD卡，格式化进程失败
21: INSTALL_FAILED//安装失败
Error code 21:0
Reason: While performing a system software update, an error was reported by the software update script.
//执行系统软件更新时，软件更新进程报错
22: DUPLEX_DISABLED//双面已禁用
Error code 22:0
Reason: The printer received a double-sided print job, but does not have duplex printing enabled.
//打印机接收到双面打印任务，但是双面打印功能未启用
23: MAG_DISABLED//磁条已禁用
Error code 23:0
Reason: The printer received a print job which required mag encoding, but does not have mag encoding enabled.
//打印机接收的打印任务包含磁条编码数据，但是磁条编码功能未启用
24: FILM_NO_COLOUR//无彩色色带
Error code 24:0
Reason: The printer received a colour print job, but does not have colour film fitted.
//打印机接收一彩色打印任务，但是未安装彩色带
25: FILM_NO_OVERCOAT//色带无保护层
26: MOTOR_FAULT//马达故障
Error code 26:0
Reason: The print engine MCU reported a dye film motor fault.
//色带马达故障
Error code 26:1
Reason: The print engine MCU reported a card feed motor fault.
//进卡马达故障
Error code 26:2
Reason: The print engine MCU reported a printhead cam motor fault.
//打印头凸轮马达故障
Error code 26:3
Reason: The print engine MCU reported a flip position motor fault while moving the card. Note that this is the flipper motor which drives the card, not the rotation motor.
//移动卡片时翻转器定位马达故障. -此为翻转器卡片驱动马达，不是翻转器旋转马达
Error code 26:4
Reason: The print engine MCU reported a flip position motor fault while rotating the flipper. Note that this is the flipper motor which drives the card, not the rotation motor.
//旋转翻转器时翻转器定位马达故障. -此为翻转器卡片驱动马达，不是翻转器旋转马达
Error code 26:5
Reason: The print engine MCU reported a flip rotation motor fault. Note that this is the flipper motor which rotates the flipper, not the one which drives the card
//翻转器旋转马达故障. -此为翻转器旋转马达，不是卡片驱动马达
Error code 26:6
Reason: The print engine MCU reported a main card drive motor fault.
//主传动马达故障
27: CLEAN_REQUIRED//要求清洁
Error code 27:0
Reason: On start-up, the printer detected that it was overdue for cleaning.
//打印机需要通过Magicard专用清洁耗材进行完全清洁
28: NO_PRINTHEAD//未检测到打印头
Error code 28:0
Reason: The printhead does not seem to be fitted.
//未检测到打印头，检查打印头是否安装并检查连接线
29: NO_SD_CARD//未检测到SD卡
Error code 29:0
Reason: The internal SD card could not be detected.
//未检测到打印机的SD卡
30: MAG_VERIFY_FAILED//磁条校验失败
Error code 30:0
Reason: While attempting to verify mag data after an encoding operation, the printer found that the data read back from the mag stripe did not match the data written.
//磁条编码后偿试校验磁条数据，读取的数据与写入的数据不匹配
31: COLOUR_DISABLED//彩色已禁用
Error code 31:0
Reason: The printer received a colour print job, but does not have colour printing enabled.
//打印机接收到彩色打印任务，但是未启用彩色打印
32: DPI600_DISABLED//600DPI已禁用
33: FILM_NO_NPANEL//色带无N面
Error code 33:0
Reason: The printer recevied a job with neutral panel options, but the fitted dye film does not have neutral panels.
//打印机接收到含有N面的数据，但是安装的色带无N面
34: FILM_NO_PPANEL//色带无P面
本文地址：http://www.fagoo.cc/n22c3.aspx，转载请注明出处。